VME-1050-PTTI
VME 10 MHz Distribution Amplifier
Key Features:
- Single-Slot 6U 32-bit VME Module.
- 10 MHz & 1PPS Inputs
- Ten 10MHz QMA Outputs
- Serial Interface via Host Bus
- Individually configurable offset and output amplitude.
Brandywine’s VME-1050-PTTI Distribution Amplifier provides ten 10MHz sine wave outputs from a single 6U x 4HP VME board. The VME-1050-PTTI features individually configurable 1PPS offsets and 10 MHz signal amplitude via a VME host serial interface.
The 10 MHz outputs are specifically designed for tight phase tracking and matching.
Other output frequency options available upon request.
Physical
6U VME form factor per IEEE P1014
Width: 4HP
Inputs
1PPS
Connector: QMA
Level: TTL
Impedance: 50Ω
10 MHz
Connector: QMA
Level: 2.0Vp-p minimum
Impedance: 50Ω
Outputs
Frequency Outputs
No. of outputs: 10
Connector: QMA
Output: Sine Wave
Amplitude: Adjusted through software
Phase variation: <1 degree
1PPS output
No. of outputs: 10
Amplitude: LVDS
Connector: VMEbus J2
Environmental
Operating Temperature: 0-50 ºC
VME-1050-PTTI Datasheet
The IBU-160i is a general-purpose frequency distribution amplifier designed for use with Brandywine high precision time sources.
The IBU-160i is contained in a compact IU rack- mount chassis. The IBU accepts two sets of inputs, comprising the reference input (100 Hz – 100 KHz) and status from the source. The IBU provides automatic changeover should one of the on-line source inputs fail. Manual source select override is available on the front panel, or through the Ethernet interface.
A variety of status indicators are located on the front panel for instant visual feedback, together with manual controls for source selection.
A 10/100 base T Ethernet interface provides full control over the functionality of the system, including reference selection and output amplitude (on a per channel basis).
User control of the unit is via a built-in Web Browser with user-friendly graphical interface, or via SNMP for system applications.
Applications for the IBU-160i include test ranges, satellite control centers, shipboard time distribution, airports, rail terminals, and any system requiring highly reliable time code distribution.
Features:
- Network Enabled Time Code Distribution Amplifier
- Dual Time Code Inputs with Auto Failover
- Support for Analog Time Codes between 100Hz and 100KHz
- Programmable per channel amplitude
- Supports SNMP v2c
- 1U 19” rack mount
- Redundant Hot Swappable Power Supplies
| Time Code Inputs | |
| Frequency Range |
Analog Time Code |
| Typical Time Codes | IRIG A, B, E, G, NASA 36, XR3, AFNOR |
| Amplitude & Impedance | 0.5-10Vp-p, 600 Ω |
| Input Isolation | Transformer coupled |
| Number of Inputs | 2 |
| Connector Type | BNC |
| Input Selection | Manual, Auto |
| Fault Inputs | |
| Number of Inputs | 2 |
| Signal Type | TTL |
| Active Level | Selectable for active high or low |
| Action | Forces on-line changeover |
| Time Code Outputs | |
| Number of Outputs | 16 |
| Format | Same as Input 100 Hz – 100 Khz |
| Output Level | 1Vp-p to +5Vp-p, short-circuit proof |
| Connector Type | BNC |
| Output Isolation | Transformer Isolated |
| Network Interface | |
| Interface Type | 10/100 base T |
| Protocols | HTTP, DHCP, SNMP V2c, IPV4 |
| Connector | RJ45 |
| Console Port | |
| Interface Type | RS232 |
| Parameters | 115200, N, 8, 1 |
| Connector | DB9 |
| Display | |
| Display Type | 16 bicolor LED |
| Functions | Output status, Ethernet settings |
| Status Output (Alarm) | |
| Type | Dry relay form C contacts Ethernet SNMP trap |
| Alarm Function | Summary of all input/output alarms (relay) Individual input, output, power (Ethernet) |
| Power | |
| Redundancy | Dual redundant Single supply maintains complete unit |
| Voltage | 90-240 VAC 50/60Hz (std), 18-36V DC Optional, 36-72VDC Optional |
| Power Consumption | <15W |
| Environmental and Safety | |
| Temperature | |
| Operating | -10 to +55ºC non condensing |
| Storage | -40 to +85ºC |
| Product Safety | EN60950-1: 2006 + A11-2009 +A1:2010 A12:2011 AS/NZS 60950-1:2011 |
| EMC | EN55022 Class A, EN50082-2, FCC Chapter 15 Class A |
| Ordering Information | |
| Basic Unit Includes Dual AC Power Supplies | |
| 19001001 | 2 input, 16 output IBU-160i |
| Power Options (order separately) | |
| 19001002 | Substitute 18-36 DC power for AC |
| 19001003 | Substitute 36-72 DC power for AC |
| Related Products: | |
| FDU-160i: | |
| 22050001 | 2 i/p 10MHz, 16 output 10MHz Low Noise |
| FDA-160i: | |
| 22050005 | 2 i/p , 16 output 1-20MHz wideband |
| The IBU-160i may be used with many of Brandywine’s precision time code sources such as the NFS220, or RTG-510 for distribution of precision time code outputs. | |
 IBU-160i |
Data Sheet |
| IBU-160i |
User Manual |
Brandywine Communication’s Havequick/1PPS Distribution Amplifier (HQS) is a small rugged, powered Havequick/1PPS distribution module mounted in a 4” x 4” x 2.5” environmentally secure enclosure. The HQS can provide an MTBF up to 1 million hours depending on configuration.
The HQS was developed to facilitate long cable runs of both 1PPS and Have Quick signals for ships or aircraft requiring these timing reference signals at multiple locations. With the tested, ruggedized enclosure the HQS can be placed in difficult environments and difficult to reach places on ships and aircraft. The unit may be configured for single ended or differential signals as required for the application (factory configured). Various power options are also available upon request. Designed for “fit and forget” operation, the compact, reliable module provides an elegant solution for distribution of the timing references from an embedded military GPS receiver.
Signal Input: Connector Type: D38999/20WB35PN 1PPS: Amplitude: 0-10V per ICD-GPS-060 Have Quick: Amplitude: 0-5V per ICD-GPS-060 Signal Output : Connector Type: D38999/20WB35SN 1PPS: No of Outputs: 3 Have Quick: No of Outputs: 3 Power Input: Connector Type: D38999/20WA98PN Power Option 1 145 VDC to 162 VDC or Power Option 2 15 VDC to 36 VDC Power Consumption: <5 Watts. Size: 3.94”x3.94”x2.36” w/o Reliability MTBF: >1,000,000 hours Environmental EMI: MIL-STD-46, CE102, CS101, CS114, CS116, RE101, RE102, RS101, RS103 Relative Humidity: 95% relative humidity, non-condensing. Operating Temp.: 0 to +50 ºC Non-Operating Temp.: -40 to +85 ºC. Air Pressure: up to +30,000 feet. Fungus & Salt/Fog: Conformally coated. Settling Dust: Base material coatings and surface treatments resilient to erosion. Operational Vibration: Shipboard Type I MIL-STD-167-1A . Transportation Vibration: MIL-STD-810F Method 514, Procedure I Categories 4, 7, 8, and 10. Shock: MIL-STD-810F [3] Method 516
Impedance: 50ohm
Impedance: 2kohm
Amplitude: 0-10V per ICD-GPS-060
Impedance: 50ohm or low Z
Amplitude: 0-5V per ICD-GPS-060
Impedance: 2kohm
3.94”x5.8”x2.36” incl. connectors
20g/15ms saw tooth pulse
The FDA-160i is a general-purpose frequency distribution amplifier designed for use with Brandywine high precision time and frequency sources. The FDA-160i is contained in a compact IU rack-mount chassis. The FDA accepts two sets of inputs, comprising the reference frequency (typically 1-20MHz) and status from the source. The FDA provides automatic changeover should one of the on-line source inputs fail. Manual source select override is available on the front panel, or through the Ethernet interface. A variety of status indicators are located on the front panel for instant visual feedback, together with manual controls for source selection. A 10/100 base T Ethernet interface provides full control over the functionality of the system, including reference selection and output amplitude (on a per channel basis). User control of the unit is via a built-in Web Browser with user-friendly graphical interface, or via SNMP for system applications. Applications for the FDA-160i include secure communications systems, manufacturing facilities, digital television broadcasting and any system requiring highly reliable frequency outputs.
Features
- Network Enabled Analog Frequency Distribution Amplifier
- Dual Frequency Inputs with Auto Failover
- Any Frequency from 1-20MHz
- Programmable per channel amplitude
- Supports SNMP V2c
- 1U 19” rack mount
- Redundant Hot Swap Power Supplies
| Reference Frequency Inputs: | |
| Connector | Two rear panel BNC's |
| Amplitude | 0.5 Vrms - 1 Vrms |
| Input Impedance | 50 Ohms |
| Frequency | 1 - 20 MHz |
| Input selection | Auto, Manual |
| Fault Discrete Input: | |
| Number of Inputs | 2 |
| Connector | DB9 |
| Level | TTL |
| Active Level | Selectable active for high or low |
| Action | Forces on-line changeover |
| Sine Wave Outputs: | |
| Number of Outputs | 16 |
| Connector | BNC |
| Frequency (MHz) | Same as input 1 - 20 MHz |
| Level | 5dBm to +13dBm, short- circuit proof |
| SSB Phase Noise (with clean-up osc. Option) | |
| Offset (Hz) | dBc/Hz |
| 1 | -132 dBc |
| 10 | -142 dBc |
| 100 | -155 dBc |
| 1,000 | -163 dBc |
| 10,000 | -163 dBc |
| Harmonics | -40 dBc |
| Cross-talk | -80 dBc |
| Spurious | -80 dBc |
| Physical/Environmental | |
| Temperature | |
| Operating | -10 to + 55°C non-condensing |
| Storage | -40 to +85°C |
| Dimensions | 19 inch Rack Mount, 1.73 inches high (1U) |
| 14.5 inches deep | |
| Weight | 7.5 lb typical |
The FDU-160i is a high performance signal distribution amplifier designed for use with Brandywine high precision time and frequency sources.
The FDU-160i is contained in a compact IU rack-mount chassis. The FDU accepts two sets of inputs, comprising the reference frequency (typically 10MHz) and status from the source. The FDU provides automatic changeover should one of the on-line source inputs fail. Manual source select override is available on the front panel, or through the Ethernet interface.
A variety of status indicators are located on the front panel for instant visual feedback, together with manual controls for source selection.
A 10/100 base T Ethernet interface provides full control over the functionality of the system, including reference selection and output amplitude (on a per channel basis).
User control of the unit is via a built-in Web Browser with user-friendly graphical interface, or via SNMP v2c for system applications.
Applications for the FDU-160i include secure communications systems, satellite ground stations, digital television broadcasting and any system requiring highly reliable frequency outputs.
| Reference Frequency Inputs: | |
| Connector | Two rear panel BNC's |
| Amplitude | 0.5 Vrms - 1 Vrms |
| Input Impedance | 50 Ohms |
| Frequency | 10 MHz |
| Input selection | Auto, Manual |
| Fault Discrete Input: | |
| Number of Inputs | 2 |
| Connector | DB9 |
| Level | TTL |
| Active Level | Selectable active for high or low |
| Action | Forces on-line changeover |
| Sine Wave Outputs: | |
| Number of Outputs | 16 |
| Connector | BNC |
| Frequency (MHz) | Same as input |
| Level | 5dBm to +13dBm, short- circuit proof |
| SSB Phase Noise (with clean-up osc. Option) | |
| Offset (Hz) | dBc/Hz |
| 1 | -132 dBc |
| 10 | -142 dBc |
| 100 | -155 dBc |
| 1,000 | -163 dBc |
| 10,000 | -163 dBc |
| Harmonics | -40 dBc |
| Cross-talk | -80 dBc |
| Spurious | -80 dBc |
| Physical/Environmental | |
| Temperature | |
| Operating | -10 to + 55°C non-condensing |
| Storage | -40 to +85°C |
| Dimensions | 19 inch Rack Mount, 1.73 inches high (1U) |
| 14.5 inches deep | |
| Weight | 7.5 lb typical |
| FDU-160i |
Data Sheet |
| FDU-160i (+15 dBm) |
+15 dBm Output Version Data Sheet |
| FDU-160i |
User Manual |
